Premera T9 Vinyl Floor Coat VCT/LVT/LVP Impervious Silicon Dioxide (SIO2) Barrier

Premera Vinyl Coat T9 Vinyl Floor Coat (aka IONYX T9) keeps vinyl and laminate flooring, as well as Luxury Vinyl Plank floring (LVP) in pristine condition, better and far longer than factory coatings. Defends against stains, scuffs, scratches, spills, dirt, mildew, and more. Uniform UV protection prevents vinyl degradation and phthalate dust formation. Vinyl Coat keeps lets you clean without harsh chemical cleaners or residue-bearing films.

T9 Vinyl Floor Coat is designed to provide a thin and durable Silicon Dioxide (SIO2) impervious coating to protect vinyl, linoleum and vinyl composition tiles and to eliminatethe need to keep stripping and waxing these types of floors which are used mainly in public buildings. Saves on water, easy to maintain by dusting or damp mop.

CHARACTERISTICS:

• Color: Dries Crystal Clear. (though it may appear slightly amber to slightly rose when initally applying and not yet cured)
• Finish: Gloss Vehicle Type: Solvent Base
• Flash Point: (C PenskeyMartens closed Cup) -9C/15F
• VOC: less than 100 g/L
• Weight per Gallon: 7.36 lb
• Provides an Impermeable Surface, Non-breathable, will not wick.

Solution For:

Scuffs, acid etching, and food and beverage stains. Laminates, Hardwoods, Linoleum, Luxury Vinyl Plank flooring, Vinyl flooring

SURFACE:

• Vinyl floor products
• Linoleum
• Vinyl Composition Tiles
• Vertical and Hoizontal applications, Floors, Walls, Ceilings

Coverage Surface Area:

• 500 to 800 sq-ft per gal
• Coverage will vary depending on the applicator, the porosity and texture of the surface.
• Recommended Spread Rate per coat: Wet mils: 2.0 to 3.0

CARE & MAINTENANCE:

• Mop periodically with plain water.
• Never use vinegar to clean the finish. An accidental use periodically is not produce visible harm, but over time, vinegar solutions will break down the coating.
• If paint or ink get spilled onto coating, this is not a problem. Simply use an approved cleaner, then rinse with fresh clean water and dry with mop.
• Although Vinyl Floor Coat is scratch resistant, it is not scratch proof. Do not use abrasive cleansers or abrasive scouring pads.
• If an area gets damaged or is mechanically abraded, lightly sand the area with 220 grit sandpaper and reapply Vinyl Floor Coat. If the substrate is damaged at the same time, make the necessary repair first, and then re-apply Vinyl Floor Coat.

SURFACE PREPARATION:

• Before applying Vinyl Floor Coat, make sure that the areas to be coated are completely clean of oils, dirt, scuff marks by using an approved cleaner.
• Make sure any loose tiles or sheet vinyl are re-glued, and in sound condition.
• For a higher shine prior to application, Vinyl floors can have 3 to 4 coats as a base of a good quality acrylic emulsion wax and burnished to desired shine.
• Any visible marks or dirt not cleaned prior to application will show through coating. Recommended: test in an inconspicuouslocation to ensure desired appearance and adhesion are achieved.
• New Vinyl Floors: Recommended: 3 to 4 coats of a good quality acrylic emulsion wax applied and burnished to desired shine as a base prior to applying the Vinyl Floor Coat. (Any visible marks or dirt not cleaned prior to the application will show throughcoating).

Existing Vinyl Floors:

• Existing vinyl floors don’t need to be stripped unless they are in poorcondition.
• Recommended: 3 to 4 coats of a quality acrylic emulsion wax as a base that is in good condition.
• Burnish the last coat to the desired shine before applying the Vinyl Floor Coat. (Any visible marks or dirt not cleaned prior to the application will show throughcoating).

Recommended: Test Vinyl Floor Coat in an inconspicuous location before applying to entire area to ensure desired results are achieved.

Important Notes on Satin & Matte finishes:

• For Satin & Matte finish products, you will receive inside the box/packaging a separate small baggie of white matting agent. 
• This matting agent has been pre-measured for your container size.
• You will need to pour the matting agent powder into the Invisible Armor container and stirr it in.
• This will then emable the Satin or Matte finish that you are needing.
• If you do not pour and stir in the matting agent, you will simply have the gloss finish.
• Also, you will need to re-stir the sealant every 15 to 30 minutes as you are using it (and before use if it has been in storage for a while).  The Matting agent does not dissolve, it stays suspended in solution and will eventually fall out (and to the bottom of the container) and need re-stirring.
• Click here if you need to purchase more Matting Agent

APPLICATION:

• Mask off any adjacent surfaces to avoid accidental coating.
• Inspect and clean one more time to make certain no pollutes got on floor after masking.
• Stir the contents thoroughly to resuspend the nano particles that have settled
• In the event of contact with skin, wash affect area thoroughly with soap and water.
• Chemical safety goggles or splash shields are required.