Maven MMA 590 - Slow Set 90-110 minutes MMA Marine-Optimized Adhesive - Thick/High Viscosity Gray or White 1:1 ratio


SKU: MV_MMA590-G_050ML

  • $ 299.99

    Maven MMA 590 - Slow Set 90-110 minutes MMA Marine-Optimized Adhesive - Thick/High Viscosity Gray or White1:1 ratio

    Maven MMA 590 is a two-part methacrylate adhesive suitable for structural bonding of various metals, plastics and composites.

    MMA 590 is a direct substitute / backup formula for the Plexus MA590.

    MMA 590 is stocked in two colors: Gray and White, and Black can be ordered also.

    And works particularly well for Marine & Boat assembly & repairs.  The product can be used for larger assemblies and for filling larger gaps. This is a 1:1-part methacrylate adhesive with an open time of 90 minutes to 110 minutes and handling strength can be achieved in 300 minutes - 420 minutes. Give excellent bond strength along with good toughness and high impact strength. Highly recommended in marine and other composite assemblies. 

    Please Note:  These cartridges are designed to work best with a 50ml or 400ml cartridge Dispenser, respectively.  We advise you use a 50ml or 400ml Dispenser for all respective cartridges.  If you do not have one, please check out our Dispensers, all are excellent products and have our 'it's good' seal of approval.

    If you prefer not to use a Dispenser, we have some 50ml kits that include hand tools or caulking dispenser adapters, as pictured, that you can use for fast small jobs.  But the 400ml cartridges really need to use a 400ml Dispenser, they're just too big to effectively use without the dispenser.

    Key Features

    • 90-110 Min Working Time (30 gm mass)
    • Medium-Set MMA for Craftsman and Industrial uses
    • Recommended for marine and other composite materials
    • High impact strength
    • Structural bonding of a variety of materials
    • Gap filling 0.75mm-15mm (.03in-.60in)
    • Excellent resistance to water and solvents

     Cured Product Characteristics

    Color: Gray or White, it can be ordered in either color
    Work life (30 gm mass): 50-70 minutes
    Handling strength: 300-420 minutes
    Full cure: 24 hours
    Mixing Ratio: 1:1

    Operating temp: -50F to 250F (-45C to 121C)

    Properties of uncured material (Resin)
    Specific Gravity: 1.0
    Viscosity@25°C, cP: 120,000 - 180,000
    Color Translucent Clear, it can be ordered in either color

    Properties of uncured material (Activator)
    Specific Gravity: 0.96
    Viscosity@25°C, cP: 150,000 - 200,000
    Color: Gray or White

    Mechanical Properties
    Tensile Strength: 2500-3500 psi
    Lap Shear Strength, psi: 2000-2500
    Modulus, psi: 70,000-120,000
    Chemical resistance: Excellent resistant to hydrocarbons, acids and bases; susceptible to polar solvents.

    Directions of applications
    Wipe off and degrease the surface to be bonded. Use eye protection and gloves to avoid skin contact. Dispense a desirable amount of adhesive using a dispensing dispenser. The nozzle sizes can be selected according to the desired bond thickness. Join the substrates with the specified work-life of this material and allow it to cure at room temperature. Do not disturb the parts during the curing process. Excess adhesive can be wiped off. (For optimum strength, surface preparation for the metals like sandblast, etching is suggested).

    Safety and handling
    Wear eye protection and gloves. Harmful if swallowed. Keep it away from heat, flames. Keep out of reach of children. Once used keep the containers closed.

    Storage and shelf life
    Store this product in a tightly closed container in a cool and well-ventilated area. Product should not be frozen. Keep it away from any source of heat. Store the material in between 51℉ to 75℉. Continuous exposure above 75℃ will reduce the shelf life.

    Welcome Newcomer