Maven ExoCoat T9EVC Extreme Vinyl Coat VCT/LVT/LVP Impervious Silicon Dioxide (SIO2) Barrier for all types of Vinyl and Linoleum Floors

Product Description

Maven ExoCoat T9EVC keeps vinyl and laminate flooring, as well as Luxury Vinyl Plank floring (LVP)  in pristine condition, better and far longer than factory coatings. Defends against stains, scuffs, scratches, spills, dirt, mildew, and more. Uniform UV protection prevents vinyl degradation and phthalate dust formation. Vinyl Coat keeps lets you clean without harsh chemical cleaners or residue-bearing films.  

Our ExoCoat T9EVC is  designed  to  provide  a  thin  and durable Silicon Dioxide (SIO2)  impervious coating to protect vinyl, linoleum and vinyl composition tiles  and  to eliminatethe  need  to  keep  stripping  and  waxing these types of floors which are used mainly in public buildings. Saves on water, easy to maintain by dusting or damp mop.

 CHARACTERISTICS:

• Color: Dries Crystal Clear. (though it may appear slightly amber to ose when initally applying and not yet cured)
• Finish: Gloss Vehicle Type: Solvent Base
• Flash Point: (C PenskeyMartens closed Cup) -9C/15F
• VOC: less than 100 g/L
• Weight per Gallon: 7.36 lb
• Provides an Impermeable Surface, Non-breathable, will not wick.

 Solution For: 

Scuffs, acid etching, and food and beverage stains. Laminates, Hardwoods, Linoleum, Luxury Vinyl Plank flooring, Vinyl flooring

SURFACE:

• Vinyl floor products
• Linoleum
• Vinyl Composition Tiles
• Vertical and Hoizontal applications, Floors, Walls, Ceilings

Recommended Spread Rate per coat: Wet mils: 4.0-5.0 Dry 

• Wet mils: 2.0 to 3.0

CARE & MAINTENANCE: 

• Mop periodically with plain water.
• Never use vinegar to clean the finish.  An accidental use periodically is not produce visible harm, but over time, vinegar solutions will break down the coating.
• If paint or ink get spilled onto coating, this is not a problem.  Simply use an approved cleaner, then rinse with fresh clean  water and dry with mop.
• Although Vinyl Floor Coat  is  scratch  resistant,  it  is  not  scratch  proof.  Do  not  use abrasive  cleansers  or  abrasive  scouring  pads. 
• If  an  area  gets damaged or is mechanically abraded, lightly sand the area with 220 grit sandpaper and reapply Vinyl Floor Coat. If the substrate is damaged at the same time, make the necessary repair first, and then re-apply Vinyl Floor Coat.

 SURFACE PREPARATION:

• Before applying Maven ExoCoat T9EVC, make sure that the areas to be coated are completely clean of oils, dirt, scuff marks by using an approved cleaner.
• Make sure any loose tiles or sheet vinyl are re-glued, and in sound condition.
• For a higher shine prior to application, Vinyl floors can have 3 to 4 coats as a base of a good quality acrylic emulsion  wax and burnished to desired shine.
• Any visible marks or dirt not cleaned prior  to  application  will  show  through  coating.
• Recommended: test in an inconspicuouslocation   to   ensure   desired appearance and adhesion are achieved.

New Vinyl Floors:

Recommended: 3 to 4 coats of a good quality acrylic emulsion wax applied and burnished to desired shine as a base prior to applying the Vinyl Floor Coat. (Any visible marks or  dirt  not  cleaned  prior  to  the  application  will  show  through coating).

Existing  Vinyl  Floors:

• Existing vinyl floors don’t need to be stripped unless they are in poorcondition.
• Recommended: 3 to 4  coats  of  a  quality  acrylic  emulsion  wax  as  a base  that  is  in good condition.
• Burnish the last coat to the desired shine before applying  the  Maven ExoCoat T9EVC.  (Any  visible  marks  or  dirt  not cleaned prior to the application will show throughcoating).

Recommended: Test  Maven ExoCoat T9EVC in  an  inconspicuous location before applying to entire area to ensure desired results are achieved.

APPLICATION: 

• Mask  off  any  adjacent  surfaces  to  avoid  accidental  coating.
• Inspect   and   clean   one   more   time   to   make   certain   no contaminates  got  on  floor  after  masking. 
• Stir  the  contents thoroughly to resuspend the nano particles that have settled
• In the event of contact with skin, wash affect area thoroughly with soap and water.
• Chemical safety goggles or splash shields are required.