DAI MMA 3010 Acrylic - Medium Set 15-Min MMA Adhesive-Thick/High Viscosity Beige-1:1 ratio

DAI Products

SKU: DAI_MMA3010_050ML

  • $ 225.00
    (We can use your FedEx/UPS acct: Type-in the needed Acct # & Service Level)


    DAI MMA3010 is a two-part methacrylate adhesive suitable for structural bonding of various metals, plastics and composites. The product does not need surface preparation or a primer. This is 1:1-part methacrylate adhesive with an open time of 15 minutes and handling strength can be achieved in less than 30 minutes. Gives excellent bond strength on various substrates.

    It works exceptionally well for Galvanized steel and surfaces specifically, which is a difficult metal to bond to, and works exceptional on most metal surfaces in general.

    Please Note:  These cartridges are designed to work best with a 50ml or 400ml cartridge Dispenser, respectively.  We advise you use a 50ml or 400ml Dispenser for all respective cartridges.  If you do not have one, please check out our Dispensers, all are excellent products and have our 'it's good' seal of approval.

    If you prefer not to use a Dispenser, we have some 50ml kits that include hand tools or caulking gun adapters, as pictured, that you can use for fast small jobs.  But the 400ml cartridges really need to use a 400ml Dispenser, they're just too big to effectively use without the dispenser.

    Key Features

    • 14-18 Min Working Time
    • Excellent General Purpose  Medium-Set MMA for Craftsman and Industrial uses
    • Beige color
    • Bonds to various metals, plastics and composites
    • Electrically Insulating (does not conduct)
    • Excellent resistance hydrocarbons, acids and bases
    • Susceptible to polar solvents
    • Lap shear 2800-3800 psi
    • Tensile strength 3200-4500
    • Modulus, psi 130,000-175,000

     Cured Product Characteristics

    Color: Beige
    Working time: 14-18 minutes (10 gm. mass)
    Handling strength: 30-45 minutes
    Mixing Ratio: 1:1

    Operating temp: -50F to 250F (-45C to 121C)
    Shore D Hardness: 80
    VOC Content: 0.1%


    Properties of uncured material (Resin)
    Specific Gravity: 1.0
    Viscosity@25°C, cP: 50,000 - 80,000
    Color Beige


    Properties of uncured material (Activator)
    Specific Gravity: 0.96
    Viscosity@25°C, cP: 50,000 - 80,000
    Color: Pale yellow


    Chemical resistance: Excellent resistant to hydrocarbons, acids and bases and susceptible to polar solvents.


    Directions of applications
    Wipe off and decrease the surface to be bonded. Use eye protection and gloves to avoid eye/skin contact. Dispense a desirable amount of adhesive using a dispensing gun. The nozzle sizes can be selected according to the desired bond thickness. Join the substrates with the specified work-life of this material and allow it to cure at room temperature. Do not disturb the parts during the curing process. Excess adhesive can be wiped off. 


    Safety and handling
    Wear safety glasses and gloves. Harmful if swallowed. Keep it away from heat and flames. Keep out of reach of children. Once used keep the containers closed.


    Storage and shelf life
    Store this product in a tightly closed container in a cool and well-ventilated area. Product should not be frozen. Keep it away from any source of heat. Store the material between 51℉ to 75℉. Continuous exposure above 75℃ will reduce the shelf life.


    We Also Recommend


    x

    ×
    Welcome Newcomer