Atlas Pro Hardwood Repair Kits for Hollow & Squeaky Floors & Staircases 50ml (1.7oz) Cartridges - Great for Hardwoods, PVC, LVP, Ceramic, and Stone floorings
Atlas Professional Hollow & Squeaky Floor & Staircase Repair 50ml (1.7oz) Cartridge Kits for Hardwoods, PVC, LVP, Ceramic, and Stone floorings. And with a variety of Epoxy set times, the kits enable you to repair / re-set loose, hollow & squeaky/creaky flooring sections and pieces by mixing and dispensing precise amounts of epoxy for efficient repairs.
Works excellently with all types of Hardwood Flooring, Engineered Hardwood Flooring, Laminate Flooring, PVC / Luxury Vinyl Planks (LVP), Ceramic Tiles, Porcelain Tiles, and Stone.
Configurable with a variety of epoxy set/working times, you have the ability to control how much time you need in order to get your job or jobs done. Ranging from fast-setting 5-minutes, 15-minutes, 30-minutes, and slow-setting 60-minutes.
By simply drilling small holes above and into the loose, hollow or squeaky areas, injecting the epoxy and adding a weight to the area while the epoxy sets, a permanent repair is accomplished quickly and economically. no stirring, pouring, or related messes.
- 1 DAI Industrial-Grade Clear Epoxy 50ml (1.7oz) Cartridge, configurable to 5, 15, 30, and 60-minute set times.
- 2 each Mixing Nozzles
- 2 each 1-inch long 14-gauge Green Needle Tips
- And additional cartridges and nozzles as needed.
- Fill-in hollow arease in flooring & staircases
- Set/Freeze movement to eliminate squeaky arease
- Fill-in knot voids and holes in rustic flooring
- Dries clear to let natural beauty show through
- Repair split boards, tiles & planks
- Apply or replace moldings
- Many other types of general repair
Instruction Sheet: Atlas Professional Hardwood Repair Kit Instructions
The Included DAI Epoxy formulas are extremely popular Clear Epoxy Adhesives. They are multipurpose, two-component, room temperature clear Epoxy adhesives with good strength and toughness. They are also an excellent bonder for Steel (ferrous and stainless), Aluminum, Copper, Tinanium, Tin, Wood, Stone, Brick, and many types of hard Plastics like ABS, PVC, and HDPE.
Please Note: These cartridges are designed to work best with a cartridge Dispenser. It is strongly advise you use a Dispenser for these cartridges. The cartridges will fit into any standard ‘Square-Back’ 50ml or 400ml Dispenser. If you do not have this, please check out the Kit that includes a dispenser, or search for the “MixPac 50ml Dispenser” or “Dripless 400ml Dispenser”.
- Work Time: varies from 5-minutes, 15, 30, and 60-minutes
- Handling Strength: about 3-4x the work time you selected.
- Full Cure Strength: 24 hours
- Color: Clear
- Viscosity: Thin Syrup (8,000 to 17,000 cps)
Typical Uncured Physical Properties:
The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Viscosity1 Base 8,000-15,000 cps Accelerator 10,000-17,000 cps Color Clear/Lt. Amber Net Weight Base 9.5-9.9 Mix Ratio (B:A) Volume : 1 1 Worklife2 10 g mixed 5 minutes 5 minutes (Gel time3) Typical
Cured Physical Properties Physical:
Color Clear Shore D Hardness 80-85 Full Cure Time5 24-48 hours @ 23°C (73°) Thermal: Wt. loss by Thermal 5% @ 307°C (585°F) Gravimetric Analysis 6 Glass Transition Temp7 33°C (91°F) Thermal Conductivity9 0.107 @ 46°C (115°F) Electrical: Dielectric Strength 860 volts/mil 1100 volts/mil (ASTM D 149) Volume Resistivity 3.5 x 1012 ohm-cm 2.2 x 1014 ohm-cm