Araldite 2050 & 2051 : Two MMA Formulas for Extreme Conditions - 2-6 Minute, Cold, Wet, Underwater Setting, Extreme Heat & Cold

Araldite

SKU: AR_2050_050ml

  • $ 27.62


    Araldite 2050 & 2051, Two very similar formulas, both with high-performance in extreme conditions and settings.  2-Part, 1:1 (equal parts) MMA methacrylate general purpose adhesive for rapid assembly operations on a wide range of substrates. These two adhesives provide excellent strength even when used at very low temperature, in moist AND even in underwater conditions. It is the perfect choice for repair jobs in very difficult, hot, cold, salty, even frigid sub-zero and arctic conditions.


    Features: For Both 2050 and 2051

    • Fast to Ultra-Fast curing from -20°C to 25°C (-4°F to 75°F)
    • Sets / Dries / Cures completely underwater, high moisture and high humidity
    • Resistant to higher temperatures
    • Excellent bond to a wide range of plastics, composites and metals
    • Minimal surface cleaning, prep, pretreatment needed
    • Max Operating Temp 284F / 140C
    • Min Operating Temp 40F / -40C
    • Excellent ageing and weathering resistance
    • Thixotropic Gel, Non-Sagging, Non-Dripping, Non-Running

    Formula-Specific Features

    2050

    2051

    Set Time (Work Life)

    1-2 minutes  

    4-6 minutes

    Handling Strength (10%)

    9 minutes

    10-15 minutes

    Min Temp for Set/Cure

    -4F / -20C

    32F / 0C

    Max Temp for Set/Cure

    77F / 25C

    104F / 40C

                                       

    Pretreatment
    The strength and durability of a bonded joint are dependent on proper treatment of the surfaces to be bonded. At the very least, joint surfaces should be cleaned with a good degreasing agent such as acetone, isopropanol (for plastics) or other proprietary degreasing agents in order to remove all traces of oil, grease and dirt. Low-grade alcohol, gasoline, or paint thinners should never be used. The strongest and most durable joints are obtained by either mechanically abrading or chemically etching (“pickling”) the degreased surfaces. Abrading should be followed by a second degreasing treatment.

    Available in cartridges incorporating mixers and can be applied as ready to use adhesive with the aid of the tool recommended by Huntsman Advanced Materials.

    Applying / Using the Adhesive
    This system is available in cartridges incorporating mixers and can be applied as ready to use adhesive with the aid of the tool recommended by Huntsman Advanced Materials. The resin/hardener mix may be applied manually or robotically to the pretreated and dry joint surfaces. Huntsman's technical support group can assist the user in the selection of a suitable application method as well as suggest a variety of reputable companies that manufacture and service adhesive dispensing equipment. A layer of adhesive 0.25 mm thick will normally impart the greatest lap shear strength to the joint. The joint components should be assembled and secured in a fixed position as soon as the adhesive has been applied. For more detailed explanations regarding surface preparation and pretreatment, adhesive joint design, and the dual cartridge dispensing system, visit www.aralditeadhesives.com.

    Temperature of application / use

    2050 : the recommended temperature application range is -20°C to 25°C (-4°F to 77°F). If the adhesive is used at a temperature above 25°C (77°F), because of the fact reaction, the viscosity will increase so rapidly that a good wetting of the substrate will be difficult to achieve. Therefore above 25°C (77°F), the performance of the bond may be limited. For higher application temperatures, the Araldite® 2051 may be preferred.

    2051: the recommended temperature application range is 0°C to 40°C (32 to 104°F). If the adhesive is used at a temperature above 40°C, because of the fact reaction, the viscosity will increase so rapidly that a good wetting of the substrate will be difficult to achieve. Therefore above 40°C (104°F), the performance of the bond may be limited. For temperature below 0°C (32°F), the ARALDITE® 2050 may be preferred.


    WARNING! The cure reaction can generate a high amount of heat, it is not recommended to mix large amounts of material at room temperature

    Storage
    Araldite 2050 & 2051 Adhesives should be stored in a dry place, in the original sealed containers, at temperatures between 2°C to 8°C (36°F to 46°F). Under these storage conditions, the product has a shelf life of 18 months for 2050, and 24 months for 2051, from date of shipment from Huntsman. The product should not be exposed to direct sunlight. The product may be placed at room temperature before use, the total time at room temperature should not exceed 6 months. Long term exposure above 25°C will reduce the shelf life of the product. The product should be never frozen.

    For additional information, consult the Technical Data Sheet (TDS) and Safety Data Sheet (SDS). Just ask us for your copy.


    We Also Recommend


    x

    ×
    Welcome Newcomer