{"product_id":"mactac-gs-rivet-tape-20-mil-rubber-transfer-adhesive-1-in-and-2-in-x-200-ft-gs1001-gs1013","title":"Mactac GS Rivet Tape, 20 mil Rubber Transfer Adhesive, 1 in and 2 in x 200 ft (GS1001, GS1013)","description":"\u003cp\u003eThe Mactac GS series is a rivet replacement tape that does the job a rivet or a screw does. Twenty mils of solvent free, high strength rubber pressure sensitive adhesive is coated onto a release liner, and that adhesive carries the load across a sign face, a panel, or a trim run without a hole drilled anywhere. The bond forms on contact under hand pressure. No cure time, no mixing, no fastener head to countersink or seal. GS1001 carries a 1.00 inch adhesive lane and GS1013 carries 2.00 inches, both 20 mil and both 200 feet to a roll. The adhesive is identical, so width is the only decision.\u003c\/p\u003e\n\u003ch2\u003eThe dry edge is what makes a rivet replacement tape workable by hand\u003c\/h2\u003e\n\u003cp\u003eThe adhesive lane is narrower than the liner on purpose. GS1001 puts a 1.00 inch lane on a 1.50 inch liner, which leaves a quarter inch of ungummed liner running past the adhesive on each side. That clean margin is something to grip. The roll does not stick to itself as it pays out, the adhesive stays off gloves during placement, and a long run can be steered with two hands on the liner instead of one hand chasing a flush edge.\u003c\/p\u003e\n\u003ch2\u003eWhy 20 mil matters\u003c\/h2\u003e\n\u003cp\u003eA 20 mil coat weight is heavy for a transfer adhesive, and the thickness is what lets it wet out surfaces thinner tapes skate across. Rough concrete, textured powder coat, routed plastic, sanded MDF. It also grips low surface energy plastics such as HDPE, polypropylene, and polyethylene, where acrylic foam tapes often need a primer before they will start. Because there is no film or foam carrier in the middle, the full 20 mil is adhesive doing bonding work, which is why it conforms to an irregular surface better than a double coated film.\u003c\/p\u003e\n\u003ch2\u003ePopular Uses\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSign faces to frames, plaques, nameplates, ADA signage, channel letters, A-frame panels\u003c\/li\u003e\n\u003cli\u003ePanel and cladding attachment, trim, architectural panels, office partitions\u003c\/li\u003e\n\u003cli\u003eGasket and seal placement, temporary clamping, staging during assembly\u003c\/li\u003e\n\u003cli\u003eRecreational vehicle interior wall and ceiling panels, trim, insulation, weather stripping\u003c\/li\u003e\n\u003cli\u003eAppliance badge and trim attachment, sound damping pads, panel bonding\u003c\/li\u003e\n\u003cli\u003eRetail fixtures, temporary displays, craft and point of purchase assembly\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eRivet Replacement Tape Performance\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eQuick tack 20 plus lbs per square inch, so parts hold the moment they are pressed together\u003c\/li\u003e\n\u003cli\u003ePeel adhesion 22 plus lbs per inch of width once the bond has wet out\u003c\/li\u003e\n\u003cli\u003eShear resistance 300 plus hours to fail, which is what lets it stand in for a fastener under sustained load\u003c\/li\u003e\n\u003cli\u003eVibration damping and moisture resistance across the full bond line, rather than point loading at fastener holes\u003c\/li\u003e\n\u003cli\u003eWorks as a third hand, holding parts in alignment while fasteners go in or a structural adhesive cures\u003c\/li\u003e\n\u003cli\u003eDoubles as a gap filler between panel and substructure where the fit is not perfectly flat\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003ePhysical Properties\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eAdhesive: GS Ultra High Tack rubber, solvent free, unsupported transfer adhesive\u003c\/li\u003e\n\u003cli\u003eAdhesive thickness: 20 mil\u003c\/li\u003e\n\u003cli\u003eGS1001: 1.00 in adhesive on a 1.50 in liner, 200 ft\u003c\/li\u003e\n\u003cli\u003eGS1013: 2.00 in adhesive on a 3.00 in liner, 200 ft\u003c\/li\u003e\n\u003cli\u003eCore: 3 in, self wound\u003c\/li\u003e\n\u003cli\u003eApplication temperature: 50F and above\u003c\/li\u003e\n\u003cli\u003eService temperature: 0F to 180F\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCompatible Substrates\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eLow surface energy plastics: HDPE, LDPE, polypropylene, polyethylene\u003c\/li\u003e\n\u003cli\u003eUHMW and corrugated plastics\u003c\/li\u003e\n\u003cli\u003eAluminum, steel, and powder coated metal\u003c\/li\u003e\n\u003cli\u003eWood, MDF, OSB, and plywood\u003c\/li\u003e\n\u003cli\u003eConcrete, masonry, brick, and cement board\u003c\/li\u003e\n\u003cli\u003eGlass and fiberglass\u003c\/li\u003e\n\u003cli\u003eCorrugated board and paperboard\u003c\/li\u003e\n\u003cli\u003eComposites and aluminum composite material panels\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eRemoving It Without Residue\u003c\/h2\u003e\n\u003cp\u003ePeel slowly from a corner at a low angle, pulling back across the tape rather than straight away from the surface. Pulling fast or at 90 degrees is what leaves adhesive behind. Clean release depends on the substrate and on how long the tape has been in place. Not recommended for wallpaper or freshly painted walls. Test the actual surface before a production run.\u003c\/p\u003e\n\u003ch2\u003eLimits Worth Knowing\u003c\/h2\u003e\n\u003cp\u003eSurfaces have to be clean, dry, and free of oil, grease, silicone, and release agents, because contamination is the usual cause of a failed bond. The adhesive is rubber based, so it is not rated for chemical, solvent, or plasticizer exposure, and prolonged direct sunlight will age it on long term exterior work. An acrylic chemistry is the better answer for years of full sun. Weight, orientation, and service conditions decide how much bond area a part needs, so size the bond rather than matching a fastener count.\u003c\/p\u003e\n\u003ch2\u003eQuestions Before You Order\u003c\/h2\u003e\n\u003cp\u003eCall \u003ca href=\"tel:8173819398\"\u003e(817) 381-9398\u003c\/a\u003e or email \u003ca href=\"mailto:sales@perigeedirect.com\"\u003esales@perigeedirect.com\u003c\/a\u003e and we will help match the tape to your substrate pair. Single rolls ship from our Dallas warehouse, so you can prove it on your own parts before buying a case.\u003c\/p\u003e\n\u003cp\u003eFOR INDUSTRIAL USE ONLY. Refer to the SDS prior to use.\u003c\/p\u003e","brand":"Mactac","offers":[{"title":"GS1001, 1 in adhesive x 200 ft","offer_id":49027816882430,"sku":"MACTAC_GS1001_1IN_200FT","price":57.0,"currency_code":"CAD","in_stock":true},{"title":"GS1013, 2 in adhesive x 200 ft","offer_id":49027816915198,"sku":"MACTAC_GS1013_2IN_200FT","price":154.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1212\/5762\/files\/Mactac-GS1-Double-Sided-Tape.png?v=1790183971","url":"https:\/\/www.perigeedirect.com\/en-ca\/products\/mactac-gs-rivet-tape-20-mil-rubber-transfer-adhesive-1-in-and-2-in-x-200-ft-gs1001-gs1013","provider":"Perigee Direct","version":"1.0","type":"link"}